Rent aerial work platforms and construction machinery in Teplice

Anyone renting aerial work platforms and construction machinery in Teplice is usually working in the glass industry or for it. The region at the southern foot of the Ore Mountains is a traditional glassmaking location, and the rhythm of the orders does not follow the building weather but the plant cycle: melting furnaces run for years without interruption, and everything that has to be done on them and on the flue gas and filter systems falls into the planned shutdown. This page shows which equipment classes suit these conditions - tall halls, hot zones, fixed time windows and platform loads calculated realistically.

A glass melting furnace is not serviced on the side. Between two furnace campaigns comes the cold repair, and only after the cooling-down period can work begin on the crown, the refractory lining, the burners, regenerators and ducts. The requirement is therefore not a single machine but a sequence - dismantling, demolition, rebuilding and relining all call for different classes. Let us know what you need as soon as the date of the cold repair is fixed; by arrangement we reserve equipment for defined time windows.

Inside the hall, on finished floors, electric scissor lifts are the basis: 6.30 to 33.00 m working height, platform loads from 227 to 1,000 kg and the largest platform area of all classes - important when demolition material and tools have to go up as well. Where indoor and outdoor work alternate, hybrid scissor lifts are the alternative, because the same machine can stay in the yard and in the hall. For confined platform levels and maintenance walkways, mast lifts with 10.00 to 12.65 m are the only class that passes through standard doorways.

Production halls in the glass industry are built high, because flue gas routing, recuperation and filter technology sit above the plant. Even during a shutdown, the refractory lining and the ducts give off residual heat for a long time, and the temperature rises towards the top - exactly where the work is done. Clarify in advance, therefore, whether the working area has cooled down and whether forced ventilation is running.

Platform load is the most frequent planning error in plant maintenance. What matters is not the number of people but the total weight of the fitter, protective equipment, cordless tools, cable drum and the component being replaced. Two fitters with this equipment are over 300 kg, which rules out the 227 kg models. Across pipework, ducts and filter chambers, articulating boom lifts with 10.89 to 48.15 m offer the up-and-over reach that a scissor lift does not have by design; outside, on chimneys and roof structures, telescopic boom lifts with 14.00 to 56.90 m reach furthest.

Mechanical engineering around Teplice works in the same types of hall, but to a different rhythm: shorter, more frequent interruptions instead of one long shutdown. The demand is for work on crane runways, hall lighting, utility lines and door systems as well as conversions on machining centres; here manoeuvrability and short set-up time count for more than maximum height, and 8 to 12 m covers the largest part. On works yards and unpaved expansion areas, diesel scissor lifts with four-wheel drive are the right choice: 9.70 to 34.00 m with up to 1,134 kg platform load.

Towards the mountains the terrain rises, and on the higher-lying commercial areas both longitudinal and lateral gradients are to be expected. For machines with a travel drive, the permissible inclination is a hard criterion: it determines whether a machine may be used on the site at all. On sloping ground, spider lifts with 13.00 to 39.50 m are the more robust choice - tracked undercarriage, low ground pressure, narrow transport width. The town's spa business plays only a marginal role for the rental fleet; there it is a matter of maintenance on existing buildings with the same indoor classes.

Telehandlers take over material transport and assembly lifting where no overhead crane reaches. Fixed models lift 4.30 to 18.80 m with 1.25 to 25 t capacity; with the matching attachments the machine becomes a fork carrier, a load hook solution or a bucket unit - during furnace relining this saves a second machine.

Excavators are available from 1.8 to 30 t operating weight, on works sites mostly in the lower and middle range for service trenches, foundations and indoor demolition. For in-plant handling, electric forklifts are the choice; in addition there are high-lift stackers with 2.70 to 5.50 m lifting height and 1.2 to 2.0 t capacity.

Every machine comes with its inspection record, CE documents and operating manual. The operator duties at the place of use follow the law of the country of use. For the Czech Republic this is Government Regulation NV 378/2001 Sb., supplemented by a separate annex for equipment for lifting loads and persons; the inspection basis for mobile elevating work platforms is CSN EN 280. In addition there are the Labour Code, Zakonik prace (262/2006 Sb.), and Zakon 309/2006 Sb.

The risk assessment and operator instruction remain with the hirer - in glass production extended by the plant's permits for work on the shut-down installation and by requirements on residual heat and time spent in the area. The daily check for visible defects and correct function remains the operator's responsibility.

Teplice is around 330 km from our site in Passau. Usti nad Labem lies immediately to the east; assignments in both towns can be scheduled in one run. We provide low-loaders and partner hauliers; we set the delivery date together with your shutdown or assembly planning. One point to clarify is whether the machine may enter the works before the window starts. For requirements lasting several weeks we invoice at long-term rental conditions.

Rent aerial work platforms → | Send an enquiry →

Before you enquire, it is worth looking at the designs: at Rent a lifting platform you will find all platform types from the scissor lift to the truck-mounted platform with their strengths, typical applications and operator duties.